murphydl Posted December 19, 2011 Share Posted December 19, 2011 I have 3 Wireless light switches (2 Button Keypads) in My house:Living RoomDining RoomSitting RoomI having alot of issues whereby they often fail to turn or off the lights. I have a number of items running in the house including:1) Baby Monitor2) Vodafone Suresignal (Femtocell) for improving Mobile signal.Does anyone know what could be causing the Wireless Light switches to be so unstable. We have tried turning off the Baby Monitor and Femtocell but they are still not reliable. Also my engineer tried chaning the Radio Channel for the Wireless switches but again they worked for a while and not unstable againThanks in Advance Link to comment Share on other sites More sharing options...
RyanE Posted December 19, 2011 Share Posted December 19, 2011 You need to get something like the WiSpy in there, and see what 2.4 GHz signals you have in your home.Then only way to fix wireless interference is to know what your spectrum looks like.RyanE Link to comment Share on other sites More sharing options...
CFUG Posted December 19, 2011 Share Posted December 19, 2011 Not only does this advice come from a high source but I have analyzed my own environ and found many potential problems. To check without such utility is tough but if you have a CA relay you can alter RF patterns a little by plugging it in at strategic locations around the affected KP. I did this early-on and it works. Link to comment Share on other sites More sharing options...
thecodeman Posted December 19, 2011 Share Posted December 19, 2011 Even if you dont have wi-spy, inSSIDer is a useful tool. Link to comment Share on other sites More sharing options...
murphydl Posted December 19, 2011 Author Share Posted December 19, 2011 Thanks alot folks for the prompt response.I have downloaded inSSIDer and will check what channels are in use when I get home later .. I wouldnt be using Wi-Spy enough too justify the cost of it.Can you clear up a few things in my head please:1) Are the Wireless Light Switches using IP to communicate with the C4 system as opposed to ZigBee?2) Would each of the Light switches then be assigned an IP Address for communication with C4?Thanks Link to comment Share on other sites More sharing options...
RyanE Posted December 19, 2011 Share Posted December 19, 2011 All of Control4's dimmers and keypads use ZigBee to communicate back to the controller.No IP Addresses involved.RyanE Link to comment Share on other sites More sharing options...
RyanE Posted December 19, 2011 Share Posted December 19, 2011 Devices with IP Addresses include touchscreens (in-wall and portable), most of the rack-mount gear (IO Extenders, Amplifiers, Audio Switches, controllers, etc.).RyanE Link to comment Share on other sites More sharing options...
murphydl Posted December 19, 2011 Author Share Posted December 19, 2011 RyanE,If there was interference across Channels should I have issues with my SR-250 Remote controls because these uses Zig Bee also .. Is this correct? Link to comment Share on other sites More sharing options...
ILoveC4 Posted December 19, 2011 Share Posted December 19, 2011 RyanE,If there was interference across Channels should I have issues with my SR-250 Remote controls because these uses Zig Bee also .. Is this correct?They do use zigbee.Do you know if your dealer has "unwound" the antenna inside the switches? Link to comment Share on other sites More sharing options...
murphydl Posted December 19, 2011 Author Share Posted December 19, 2011 I can check re: the Antenna ..The following is my Lighting setup:Take one Room for example, Basically I have 3 Circuits on the same Light Switch ..Circuit 1: SpotsCircuit 2: Centre LightCircuit 3: Wall LightsThe way my lights are setup then area) Living Room Light Switch - Is basically a 2 button Wireless Switch 3 x 2 button wireless dimmers [http://www.nextgenhome.co.uk/products/UKIL-500_Control4_Wireless_Dimmer.php] (1 per circuit mentioned above). I had to replace my Wireless dimmers after 2 years of using the system last year at what I consider a big cost and now I have issues again with the same thing.To say Im a bit frustrated at the moment is an understatement but Thanks for your help guys. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.