I'd run CAT5e personally.

Hey, if had my way back in 2008, I would have fiber in the troughs right now.  Just run CAT 6 and plenty of it.  In 2015 you'll wonder why you ever lost sleep over cost.

Last edited by Controlfouruserguy (Oct-17-2011 08:45 PM)

Give me a wired connection any day. Spectrums are too crowded, wireless n spec seemed to take forever to materialize out of draft form, you can put a ton of stuff down fiber like gig ethernet, control, etc in addition to hdmi 1.4 features.

Check the thickness and flexibility of the cable. I don't know about 6a, but 6 is way more difficult to pull thru conduit and bend around tight corners than 5a. Gogodelicious is the fibre expert

scrunchy wrote:

From what I read, for shorter distances (up to 120 feet when bundling a bunch of cables together or 180 feet otherwise) you can run 10-Gigabit network over Cat6.  Cat6a can be used to run 10-Gigabit network over longer distances (330 feet).

Cat6 also give better insulation.... whether or not anyone needs that... who knows...

We're just building our house now and had Cat6 STP run everywhere.  Where we live we were charged 20% more per foot for Cat6 vs Cat5e.

Thanks for the reply.  It is interesting to hear what other people are doing.  The low voltage company I have to use did not want to deal with Cat 6. 

That is interesting on the Cat 6 vs. Cat 6a distance comparison.  Why did you go with shielded runs?  Will the installer actually be grounding the shield to the keystones?  I looked through the showcase section of these forums and did not find any examples of grounded installations in their racks.

Glenn

My entire home uses Cat6A STP with a 6 strand fibre backup run to each drop . Could not be happier with this decision. Networking, HDMI distribution is all flawless and blazingly fast

It will take the installer a few terminations to get the hang of it and then its probably 15% longer per connection. No biggie for getting a 10G ready network. If you want pictures I can through up a few of the patch panels in the racks etc. Let me know.

qVAMPIREp


I see there is interest in the previous posts so here you go guys. Note the diameter of the Cat6a STP in picture 2 is about the same or slightly larger than RG6

Last edited by qVAMPIREp (Oct-21-2011 12:37 AM)

i am installing my own network in my house now and i would have to say that going CAT6a STP was the best thing i have done so far....it might be harder to run and thicker to get through tight places but it will be worth it in the end when you dont have a bottle neck bc or your wiring...and also interference

tbear1 wrote:

qVAMPIREp wrote:

My entire home uses Cat6A STP with a 6 strand fibre backup run to each drop . Could not be happier with this decision. Networking, HDMI distribution is all flawless and blazingly fast

qVAMPIREp

Wow.  Really nice install.  What are the specs for the two racks (middle Atlantic 32U?)

Glenn

They are both ERK-2725 27U on wheels. Nice working height for the modems and NAS drives but the ERK-3525's might have been slightly better perhaps.... I've got too many gadgets I guess

qVAMPIREp wrote:

They are both ERK-2725 27U on wheels. Nice working height for the modems and NAS drives but the ERK-3525's might have been slightly better perhaps.... I've got too many gadgets I guess

The ERK series has a nice look to it.  Your system is the first one that I saw with two 'shorter' racks together.  It looks well balanced. 

Spicoli

We use Cat6a on some items and I have a ton of it in my house.  Its all UPT non-shielded which isn't a ton of money (but its more no question about it).  From modular connector to modular connector its no problem at all.  I even have a rapid tool to terminate both ends but terminating it in an RJ 45 jack is next to impossible.  I've purchased the unofficial Cat6a jacks (I say unofficial because you are only supposed to do terminations to RJ 45 in the factory to maintain the rating) but those jacks don't work very well at all.  If there aren't many runs, its usually more cost effective to terminate to a modular jack and use a 3" Cat6a patch cable. 
Its 10 times faster than Cat6, should be sufficient for future proofing for a year or two

CAT6 UTP for data, audio, intercom, etc and CAT6 STP for video.  Would run STP if i could but our prewires already cost way too much for our clients as we futureproof for all distribution.  If you are utilising B&O hardware CAT7 is their standard from now on.

Speaking of distribution i am impressed by the new Crestron DM distribution.  1 CAT6 STP cable can do hdmi video, audio, ethernet and control.  Only thing it doesn't do is audio return.

qVAMPIREp wrote:

My entire home uses Cat6A STP with a 6 strand fibre backup run to each drop . Could not be happier with this decision. Networking, HDMI distribution is all flawless and blazingly fast

It will take the installer a few terminations to get the hang of it and then its probably 15% longer per connection. No biggie for getting a 10G ready network. If you want pictures I can through up a few of the patch panels in the racks etc. Let me know.

I'm about ready to order a NextLAN Cat. 6A solution, but I'm torn between the AXi (10Gain XP UTP cable) and the shielded (U/FTP cable) solution. Any particular reasons why you went shielded? My concern with a shielded solution is that it is much harder to meet the Category 6A specification for short links. This limits most of my runs to a minimum of 15 m, which limits the number of drops i can do with 1000 ft of cable.

I'm just wondering what were your reasons for choosing U/FTP or UTP?